824 WindowTouch-4e
824 WindowTouch-4e
The new 824 WindowTouch-4e brings you:
1. Easier and faster tooling setup combined with the most reliable fastener feeding.
2. Best workpiece accessibility.
3. Easier and faster programming.
4. Best Operator Ergonomics.
5. Energy Saving.
1. Easier and faster tooling setup combined with the most reliable fastener feeding.
2. Best workpiece accessibility.
3. Easier and faster programming.
4. Best Operator Ergonomics.
5. Energy Saving.
Easier and Faster Tooling Setup
A: MAS 350 – new Modular Autofeed System
A unique new drive system in combination with a complete new bowl design incorporating all the latest bowl feeding
technologies.
A long list of advantages, but what does this mean to you?
A unique new drive system in combination with a complete new bowl design incorporating all the latest bowl feeding
technologies.
A long list of advantages, but what does this mean to you?
- Tool Change reduced from 3 minutes to 3 seconds through a one piece tool module.
- No more manual bowl settings required. Software automatically sets the proper vibration rate, air eject time and required air pressure to allow for failure free fastener feed. ‘From a full bowl down to the last one out.’ Reliable Feeding. Faster Changeover. No Training Required.
- Larger bowl design in combination with new drive allowing for fastener sizes M1.5 through M10 all to be fed in the same
bowl. - Deeper Bowl design in combination with new bowl tooling design allowing for fastener lengths up to 40mm all to be fedin the same bowl.
- New drive design allows for a 1 single tool piece, resulting in faster and easier tool changes.
- Change in bowl material resulting in fasteners becoming less dirty from ‘airdust’ or individual rubbing.
- Lower mounting position allowing for easier filling and emptying.
B1: New T-Bracket and Shuttle with integrated Connectors eliminating alignment challenges. Fastest and easiest setup in the industry.
Reduced from 2 minutes to 10 seconds without having to think about which connector goes where. On traditional machines, an operator had to change multiple air-lines and sensor cables, unnecessarily delaying changeover times.
In addition, operators required training for alignment of the T-Bracket and shuttle, which has been eliminated with this new system.
New re-designed Shuttle Plate Jaw Pins, eliminating breakage and saving cost for replacement and downtime.
B2: Pre-aligned Base Plate.
A pre-aligned base plate allows for easy tool holder changeover. No alignment of tools required. Where a tooling re alignment after tool holder replacement used to take up to 5 minutes, this setup time has now been completely eliminated.
C: Integrated Tooling Storage.
Easy and transparent storage of Multi- Modules for the MAS-350 autofeed in combination with separate storage for the
Shuttle Modules and upper and lower tools.
Both storage positions located where you need the tooling, eliminating unnecessary searching and walking around, allowing for faster and easier tooling changeovers.
824 WT-4e Machine Specifications and Dimensions:
| Force Range | Adjustable 225 lbs. (1kN) to 16000 lbs. (72kN) - Optional 20000 lbs. (90kN) modification available |
| Throat Depth | 24” (610mm) |
| Stroke Length | Adjustable 0 to 8.5” (0 to 220mm) |
| Electrical | 208 to 575V 3 phase - 50 or 60 Hz |
| Motor | 5 HP |
| Oil Tank Reservoir | 22 gallons (83 liters) |
| Speed | up to 2000 insertions per hour |
| Repeatability | +/- 2% of force setting |
| Footprint | (LxWxh) 59” x 38” x 94” (1499mm x 966mm x 2388mm) |
| Fastener Range | 256 to 1/2” (M2 to M12) |
| Clinching Capability | 22 gage to 11 gage Steel (1mm to 6mm) combined thickness |
